Features & Options
Product features include:
Direct Servo technology
All our subwoofers feature our Direct Servo
technology, which is our secret to achieving tight and accurate
bass. The benefits are far more than simply achieving low distortion
(the amp below does not depict the actual control layout).
Learn more in our technology articles
Driver features include:
- Rigid one piece dish shape black anodized
aluminum cone ensuring control at high SPL
- Low moving mass to ensure an exceptional transient response
- High flux density in the gap to ensure low distortion
- Flux de-modulation shorting rings to lower
inductance and improve linearity
- Extended upper bandwidth response allowing a higher crossover point than most
While designed primarily for their sound quality, these custom designed drivers are also stylish in appearance with a anodized aluminum cone and rubber surround. Unfortunately, it's not possible to judge the accuracy of a driver by observing its appearance. There are other drivers on the market which in fact look quite similar, and it's tempting to think that they are comparable. Many of them are inferior in performance due to a heavy moving mass, the absence of shorting rings, wider gaps around the voice coil and high inductance which limits the useable high frequency cut off point. Many aren't suitable for a crossover point higher than 50 Hz. This is very limiting when one considers the large number of home theatre speakers which perform better when relieved of bass duties.
Read more
Quality enclosure
Our enclosures are very solid and well braced to minimize any cabinet resonances or coloration. The baffle into which the driver is mounted is double thickness.
Available finishes for E22:
- piano black
- black oak vinyl
Bass extension controls
All of our subwoofers feature unique bass extension controls which are not normally provided on subwoofers. This enables the user to customize the output and extension to achieve the best compromise in any room. Most subwoofers neglect to provide bass extension control, and the result is that dynamic headroom is compromised.
|
The bass extension
controls enable the user to customize the frequency response
of the low end. The controls customize a high pass filter to
set up the corner frequency of bass roll-off. The damping control
determines the steepness of roll-off and the amount of time
domain ringing. High damping provides the least amount of time
domain ringing and the most gradual roll-off curve. Low damping
provides the steepest roll-off at the low end at the expense
of added time domain ringing. Low damping is more suitable for
HT use. 14hz setting with Low damping setting is recommended
for HT. 14hz high damping is recommended for music. |
Crossover options
To suit different setups,
we provide a 12 db and 24 db/octave crossover. If you are using
an AVR, then we recommend "AVR/12" (or EXT/12 in older
amps). If you are still using stereo receiver or conventional prea/power
amp setup, then we recommend the 80hz/24 db/octave setting. To understand
more about how to correctly integrate your subwoofer, read our phase
alignment article.
Balanced professional version
|
For professional use,
a balanced input version is available. The sub The outputs
allow multiple subwoofers to be connected. Simply daisy chain
the connections, running output from the first (master) subwoofer
to the input of the next.
For home use, balanced connections are not normally required. However, for those using studio processors and EQ units with balanced outputs, this option may be more convenient. If connection to a source with RCA connectors as found on my home audio equipment, an adaptor may be used. In this case it should be noted that the connection can no longer be considered balanced. |
For more information, including charts showing response with different settings, view our amplifier page
PEQ parametric version
|
The amp has one band of parametric EQ with
adjustable frequency, gain and bandwidth. This means you can
not only control the boost or cut, but also the width of the
filter.
Additional bass management options are also provided. A switch allows the user to select a 12 or 24 db/octave crossover slope setup option. Where the higher slope (24db/octave) is selected, the amplifier uses a variable 12db/octave filter in addition to a fixed 12db/octave filter. One can choose with a switch the corner frequency of the fixed filter as either 50 or 80 Hz, which will suit most situations. The variable filter can be used for fine tuning. |
More information
Continue to Performance & Specs |